It's about pools on the floor
People talk about downlights as if they're little lamps that light a room. They're not. Each one throws a cone, and what you're actually designing is how those cones land on the floor, the worktop, the table — not what the ceiling looks like from the settee. A ceiling full of evenly spaced circles is a lovely thing to photograph and a rotten thing to live under.
So you're aiming for overlap. The pool from one fitting should run into the pool from its neighbour so there's no dark bridge between them, but not so far that you've basically built a flat white sheet overhead. There's a middle ground where you get soft scallops of light with gentle shading between, and that's the one you want. Too tight and it's a wash. Too wide and it's a disco floor.
Catalogue photographs often show broad white rooms with sparse furniture and a perfectly ordered grid. Real kitchens contain wall units, extractors, tall refrigerators and projecting shelves that intercept light. Their floors may also be much darker than the photographed ceiling. Use those images for visual references while designing from the actual furniture plan and finishes. A repeated pattern copied without those details can produce a result that looks orderly overhead but leaves the work in shadow. The useful test is how light reaches occupied surfaces, including the areas where people stand between a fitting and the task.
Ceiling height is your first ruler
Before you do anything, look up. The height of the ceiling is your starting point, and you don't need a laser level to get the sense of it. Tall room — high ceiling, old Victorian terraced house with the plaster pulled about — and you can spread the fittings out a fair bit, because the cones have room to open before they hit the floor. Low ceiling, a modern extension or one of those new-build kitchens where you can touch the ceiling flat-footed, and they need to come closer together, or the light lands in tight hot spots right under each one.
Picture the beam at the height of the surface being lit. A greater drop allows the same distribution to spread farther, although the illuminance and overlap still need checking. A worktop receives a smaller footprint than the floor beneath it because it is closer to the ceiling. Generic spacing rules can help sketch an initial layout, but they do not replace the photometric information for the chosen fitting. Compare the beam distribution, mounting height, surface finish and task requirements together. A plan for food preparation needs a different assessment from one intended to provide soft background light around seating.
In a tall room, wider spacing may create useful overlap with a suitable optic, while the same layout under a low ceiling can leave isolated bright patches. Test the relationship using the actual mounting height rather than borrowing a successful arrangement from another property. Check the edges of each pool as well as its centre. A broad beam may soften transitions but can also reveal the source from more viewpoints. Use the sample and lighting calculation to find a balance between coverage, brightness and comfort. Ceiling height provides a starting condition; it does not decide spacing by itself.
The wall gap matters more than you think
Placing fittings close to every wall can make a ceiling look neatly bordered while producing hard scallops down the plaster. Decide whether the wall should receive a controlled wash, accent grazing or only background light. Each intention calls for an appropriate optic and offset. A general downlight pressed near the perimeter may create stripes that draw attention to surface imperfections. Inspect that effect with a sample before repeating it around the room. The doorway view is useful for judging composition, but the wall treatment needs assessment with the light switched on.
Give the wall offset a clear reference. Where cabinets project into the room, measure against their fronts as well as the underlying wall so the light reaches the worktop instead of stopping on the doors. Include the person standing at the counter in the check. The appropriate offset depends on the optic, cabinet depth and task position, so a single distance cannot solve every kitchen. Mark the proposed row and trial the light before cutting all openings. A small shift can change both the useful worktop illumination and the brightness of the cabinet fronts.
The other thing about the wall gap is that it depends on what's at the wall. In a working kitchen, the run under the wall units usually doesn't need much from the ceiling — a bit of fill, that's all. In a sitting room, the row near the wall is where the armchair goes, and you want a gentle pool that picks out the corner rather than a stripe down the chimney breast. Same distance, different intent. That's the bit you can't get out of a catalogue.
Let the furniture vote
Here's the one that sorts out most of the arguments: the furniture is part of the design. The dining table wants a fitting or two over it, roughly centred on the table, not on the room — because if the table's off-centre (and it nearly always is, once you've worked around a radiator or a door swing), the light tells the truth. Put the fitting over the middle of the room and the table sits half in shadow, and the customer will never quite say why the room feels odd.
Treat a kitchen island as its own lighting zone with positions related to its final dimensions. Coordinate those positions with joinery and any pendants rather than extending the general grid automatically. In seating areas, check where a reclined occupant will see the source. A fitting over a pillow or immediately above the head can put bright light into an uncomfortable sightline. Moving the row so useful light falls in front of the sofa may work better, depending on the optic and task. For reading, compare the position with the actual chair and book, avoiding shadows from the user's head or hand.
If there's a proper table in the middle of the room, and a sofa at one end, and an island at the other, those are three different lighting jobs sharing a ceiling. Treat them like it.
More fittings isn't the cure for a dim corner
A gloomy corner needs diagnosis before extra fittings are added. Check whether a tall appliance blocks the beam, whether the nearest row misses the working surface or whether a dark finish absorbs more light than expected. Adding units to the same unhelpful pattern can increase the count without resolving the cause. Compare a changed position or an appropriate task layer first. Inspect the corner from its normal use position, because an area that looks dark from the doorway may not be a task area at all. The desired result is useful visibility where needed, with suitable background light elsewhere.
An excessively dense grid can flatten the room's appearance. Similar brightness everywhere removes the hierarchy between work surfaces, circulation and quieter seating. Discuss which areas need emphasis and which can remain more subdued before increasing the count. A comfortable room can contain shading without leaving important tasks difficult to see. Compare the scene at the intended dimming level, since a bright commissioning demonstration may conceal the character of an evening setting. The plan should support the occupants' activities rather than pursue uniform brightness across every visible patch of floor.
If a corner's genuinely dark after you've sorted the spacing, look at what's there. A wall unit blocking the drop, a darker floor, a shadow from a fridge. Usually a small move — a fitting nudged out, a row pulled away from the wall — does more than doubling the count. If it doesn't, then talk about a runner or a bit of task light, not a ceiling full of holes.
Open-plan isn't one room
An open-plan room wants treating as three rooms in a line, and the fittings should change as you go along. The kitchen end: closer together over the working zones, tight over the island, and generous over the run by the wall units so the worktop's lit properly. The dining middle: fittings centred on the table, wider apart, because a table only needs a pool over it and a bit of fill around, not a lattice.
At the sitting end, assess wider spacing and positions that keep sources away from reclined sightlines while providing the required light. The change from cooking to dining to seating can establish a useful rhythm along the room. Carrying one dense grid through all three areas can make the seating feel like an extension of the work zone. Compare independent controls as well as different positions so the kitchen need not dictate the evening scene. Use the furniture plan to locate the transition and test from the sofa, where the room is experienced for longer than a quick walk-through.
The one to watch is the crossover — that bit where the dining table sits close to the sofa. Pull the row back, keep the pool on the table, and don't let the sitting-end row creep towards the middle just to fill the gap. A small shading between zones is a good thing. It tells your eye the room has ends to it.
Tape it and test it before you cut
Tape the positions on the ceiling before cutting. Mark the centres and leave enough time to view them while the room is being used normally. Check the marks in daylight and after dark, with the table, chairs and movable furniture in their intended positions. A layout based on an assumed table centre can look noticeably wrong when the real furniture arrives. Adjust the marks while the change is still reversible. Record their final dimensions from stable references so an installer does not recreate an earlier version by mistake. This setting-out stage is particularly useful where several lighting zones share one open ceiling.
Then trial a real fitting or representative sample arrangement. Match the intended mounting height and assess it at night with the other planned layers operating. Daylight can hide hard scallops and dark gaps that become obvious after sunset. One fitting shows its beam footprint and source visibility, while adjacent samples or a calculation are needed to judge overlap across a row. Avoid assuming that one attractive pool guarantees the complete layout. Resolve any concerns before repeating the openings. The aim is to reduce irreversible work while there is still room to adjust the spacing, wall offset or optic.
A successful final check returns to the problems identified at the start: transitions between pools, cabinet-front brightness and visibility at the working surface. Walk the room and stand where cooking, reading and circulation actually happen. Compare the result with the marked plan and record any changes made during the trial. Keep that updated drawing with the fitting references so maintenance and later alterations begin from the installed arrangement. Repeated measurement and observation provide a more reliable basis for spacing than visual symmetry alone. The completed ceiling should support the room below it as well as look coherent from the doorway.