The dotted line is a fiction
A catalogue can encourage a dotted line of fittings along every eave, with extra units up the gable and around the rear. Before adopting that pattern, mark the tasks each unit would serve. Some positions may illuminate the approach, while others add brightness without helping anyone find the door or step. Compare a restrained task-based layout with the full perimeter arrangement. The initial count should follow the route and the architecture rather than the number of equally spaced dots that fit on a photograph.
Here's the thing. Light's cheap to buy and expensive to live with. A house lit edge to edge looks like a car park. What you actually need is enough light to do the jobs the outside of a house has to do after dark: find the door, find the step, find the turn in the path, see who's at the gate. Everything past that is decoration, and decoration on a soffit tends to mean a fitting every few metres that nobody ever looks at except the neighbours.
For a low bungalow, a reduced layout focused on the door, step and useful approach points may provide a more composed appearance than a continuous illuminated border. Trial the effect before purchasing the full quantity. Keep the distinction between functional positions and decorative accents clear on the plan. That makes it easier to remove unnecessary fittings while retaining enough light for visitors and ordinary household use after dark.
Symmetry's the other trap. The eye wants fittings evenly spaced because that's how the catalogue photos are taken, but the path isn't even, the door isn't centred, and the step's off to one side. Light the route people walk. If that means two fittings bunched at the door end and a gap of six metres to the next one, so be it. Nobody's measuring your spacings from the pavement.
Light the door, the step, the turn
Start at the door and work outwards. The door needs to be readable from the gate — not floodlit, readable. You want to see the bell, the number, the keyhole when you're fumbling for it. Then the step, because a step you can't see is a step you trip on, and that's the sort of claim nobody wants on their house insurance. Then the turn in the path, wherever it happens to be, because that's the bit where visitors hesitate and look daft.
This is where a soffit light earns its keep over a wall lantern, mind. Mounted under the eave, aimed down and slightly back towards the wall, it washes the door and the step without throwing a hot spot in your face. Aimed out towards the path it does the turn as well. Two fittings at the door end of a run of eaves will do more for a house than eight spread evenly from gable to gable.
On a corner plot, the approach may run along the side and turn sharply toward the entrance. A neat front-elevation row can leave that turn in shadow even when the facade is bright. Check whether a suitable adjustable fitting can direct useful light along the approach without exposing its source to visitors or neighbours. Test the revised aim before adding more units. One well-positioned beam can address a missed turn more effectively than increasing the count elsewhere along the eaves. Keep the decision tied to the walking route.
Weather comes in sideways
Now the bit that separates a proper install from a catalogue order. An eave keeps the rain off when it falls straight down. It does almost nothing when the wind's driving it in sideways, and that's exactly what happens on the exposed side of a house — the prevailing side, the corner that catches everything, the gable end where the rain comes at the wall like it's got a grudge. Mist does the same job slower. It gets into everything and sits there.
Match the maker's stated suitability to the particular elevation and installation detail. An exposed corner can receive driven rain that a sheltered porch does not, even though both positions are technically beneath an eave. Give the installer photographs and orientation information alongside the fitting instructions. Include joints, cable entries and any separate enclosures in the assessment, because the complete installation must suit the exposure. A general outdoor description cannot explain every condition at a particular wall. Resolve those questions during selection and retain the relevant documents with the installation record. If the proposed assembly does not suit the exposure, change the product or location before work begins rather than relying on the overhang as universal protection.
A corner exposed from two directions deserves a specific check. Water can reach the assembly through routes that are not obvious from a straight-on elevation view, and a return visit at height adds cost and disruption. Inspect the shelter, mounting orientation and connection detail together. Use the manufacturer's applicable instructions and the installer's assessment to decide whether the proposed arrangement is suitable. Record the decision before the fitting is installed so the exposure assumptions remain clear during later maintenance.
Every fitting needs a ladder one day
Access is the real design problem and nobody wants to hear it. The light you can't get to is the light that ends up dirty, dead or full of spiders, and it stays that way for years because getting to it means a ladder on uneven ground, or a ladder over a flowerbed, or a ladder through a gate that's too narrow to open properly.
Before marking positions, assess how each fitting will be reached safely for inspection and maintenance. Look at the ground below it, including slopes, soft grass and narrow paths. Note downpipes, gates, conservatories and parked vehicles that could obstruct access. A location above a lean-to roof may appear convenient on the elevation but require specialist access in practice. Do not treat standing or crawling on a fragile roof as a maintenance method. Ask the responsible contractor to assess an appropriate access arrangement and include that cost in the comparison. A small change in position can sometimes preserve the lighting effect while making future work substantially more practical.
Same goes for cleaning and replacement. Every fitting's going to need both eventually, and the ones you can reach in a couple of minutes with a step ladder are the ones that stay working. The ones you need to plan a morning for are the ones that get ignored until someone sells the house. If the access is genuinely awkward, fewer fittings in reachable spots beats more fittings in clever ones. Always.
Tenants you didn't invite
Soffit lights can attract insects and accumulate webs, especially in sheltered corners. Dirt across a lens can change the visible beam, while obstruction near a sensor may affect its response. Birds may also use eaves for nesting, which requires a separate, appropriate approach to wildlife protection and maintenance timing. Include these possibilities when selecting accessible positions. A fitting close to a known nesting area may create cleaning and disturbance problems that a slight relocation could avoid. Plan inspection as part of upkeep rather than assuming the lens will remain clear between electrical repairs.
You plan round it rather than fight it. Keep fittings away from the corners where nests go up, and away from the bit of wall directly above a favourite perch — nothing worse than a light under a regular bird landing spot, because you know what lands with the bird. If the customer's happy with the birds (most are, until the car gets hit), give the nest corners a wide berth and put the light where it's actually needed. If they're not happy, that's a different conversation and not one for the lighting plan.
If a sensor-controlled light behaves unexpectedly, check for accessible dirt, webs or insects as part of a safe maintenance inspection. Do not assume every change in switching indicates an electrical fault, but do not open live equipment or dismiss persistent symptoms without assessment. Follow the cleaning instructions and have unresolved behaviour investigated by a competent person. Explain ordinary cleaning and sensor checks at handover so the owner knows which tasks are routine and which require professional attention.
Down at the wall, not into the street
Aim matters more than most of the kit. The instinct is to point soffit lights out, into the garden, like little floodlights. Don't. Out means into the neighbours' windows, into the street, into the eyes of anyone walking past, and into the eyes of the driver coming up the road at half eleven. Aim them down at the wall and the path. Narrow-ish spread, close to the wall, grazing down the render or the brick and pooling on the ground where feet go. That's what makes a house look cared for rather than lit up.
Warm white, not ice white. Ice white on a house at night looks like a shopfront and everyone within three doors will have an opinion about it. And whatever you fit, put it on a timer or a sensor so it comes on when it's useful and goes off when it isn't. Lights burning till dawn every night of the year are the fastest way to fall out with a neighbour, and it's not doing the door any favours at four in the morning either. A sensor at the gate side and a timer for the rest does nearly everything most houses need.
Finish by checking the aim from the gate and along the route with any assessment torch switched off when safe. Look for direct views of the luminous source, dark steps and spill toward neighbouring windows. If the source is exposed, review its shielding, position and aiming angle rather than accepting glare as an unavoidable part of exterior light. Confirm that the door, step and path are readable, then check the timer or sensor behaviour. Record the final settings so a later adjustment can be compared with the accepted arrangement.